Colorcoat Prisma®

Produkto aprašymas

Colorcoat Prisma ^® by Tata Steel

The Colorcoat Prisma® products introduce a breakthrough innovation by using the latest three-layer technology to produce an optimized, durable, chrome-free coated sheet.

Colorcoat Prisma® not only uniquely shifts the limits of UV resistance parameters, but also exceeds the most

stringent European corrosion resistance standards. It is therefore the ideal choice for commercial, retail, warehouse, public and aesthetic buildings that are built with durability in mind.

Product advantages

Revolutionary 3-layer coating technology, ensuring increased aesthetics, durability and long-term operation.
The Confidex® Guarantee for up to 40 years for industrial and commercial building facings exposed to the external environment remains valid without the need for inspection and maintenance.
Optimized Galvalloy ™ metallic layer provides maximum corrosion resistance and cut edge protection.
Independently tested for volatile organic compounds (VOC) according to EN ISO 16000-9, with an A + rating.
Full compliance with REACH requirements; chromate-free, including hexavalent chromium.
Made in Great Britain. The product is certified in accordance with the BES 6001 responsible sourcing standard.
Full compliance with the certification of BREEAM and LEED systems.

properties	type of examination	color	Results
coating thickness	EN 13523-1	uniform, metallic and matte	65 μm
coating thickness	EN 13523-1	Elements	40 μm
flexibility – resistance to bending cracking – minimum bending radius – T (mm)	EN 13523-7	all	0.5T to 16ºC
flexibility – impact resistance – J	EN 13523-5	all	≥ 18
adhesion – cross cut (%)	EN 13523-6	all	100
scratch resistance – pencil hardness	EN 13523-4	all	H.
specular gloss – Gardner 60º	EN 13523-2	uniform and metallic	25-35 GU
	EN 13523-2	matte	<10 GU
	EN 13523-2	Elements	30-40 GU
abrasion resistance – Taber, 250 revolutions, 2 kg, CS10) – (mg)	EN 13523-16	uniform, metallic and matte	<15
	EN 13523-16	Elements	<15
corrosion resistance category	EN 10169	all	RC5 CPI5
corrosion resistance – salt spray (hours)	EN 13523-8	all	1000
resistance to moisture (hours)	EN 13523-26	all	1500
category of resistance to UV radiation	EN 10169	all	R _UV 4
maximum tem. continuous operation ( ^o C)			90

CONFIDEX GUARANTEE PERIODS

Zone 1	*	solid, metallic and matte colors
Zone 1	*	Elements colors

Zone 2	*	solid, metallic and matte colors
Zone 2	*	Elements colors

The warranty periods for locations in the coastal strip apply to buildings located up to 1 km from the coastline.
For complete Confidex® Guarantee terms, please see the online application form available at www.colorcoat-online.com/registration.
In order to remain valid, the Confidex® Guarantee must be registered within 3 months of the building completion date.
The Confidex® Guarantee periods shown in the above illustration apply to Zone 1 and Zone 2. More information on other zones can be found at www.colorcoat-online.com/confidexmap

Warranty coverage zones

Zone 1 – Northern Europe	Ireland, UK, Denmark, Sweden, Norway, Estonia, Latvia, Lithuania, Poland, Czech Republic, Slovakia, Germany, Netherlands, Belgium, France, Luxembourg, Switzerland, Austria, Hungary, Slovenia
Zone 2 – Southern Europe	Portugal, Spain, Italy, Croatia, Bosnia and Herzegovina, Serbia, Montenegro, Kosovo, Macedonia, Albania, Romania, Greece

In the case of areas outside the Confidex Guarantee zones – please contact us for additional information.

MAINTENANCE AND WASHING

Maintenance and washing

In order to extend the service life of roofs and facades made of coated metal sheets, they should be regularly inspected and maintained.

Inspection – Once a year (preferably in spring), the roof / facade should be inspected for early detection of possible damage.
Sheet cleaning – Roofs / facades made of coated sheet metal require cleaning at least once a year. Dirt settling on the sheet can cause uneven discoloration (the result of uneven exposure to UV rays), as well as reduce corrosion resistance (dirt retains moisture on the sheet and gradually damages it). Dirty and stained places can be cleaned with a soft brush and water (max. 60 ° C). If necessary, it is allowed to add a mild detergent to the water (pH 6 ÷ 7, max. 10% solution). Pressurized water (max. 100 bar) can also be used for cleaning, however, the water jet should not be applied too close to the sheet surface (min. 30 cm), and should not be directed perpendicularly to the surface. At the connectors, the stream of water should be directed downwards so that to prevent pressurized water from penetrating the gaps around the fittings. Old coatings should be handled with extreme care. Washing should be carried out from the top downwards and the cleaned area should be immediately and thoroughly rinsed with clean water.
Scouring powders, nitro solvents, chlorine solutions, aromatic agents as well as agents containing ammonium chloride or sodium salts must not be used.
Damage – Repairing any damage during the warranty period should be consulted with the roof / facade contractor and may only be performed with his approval. Damage to small areas is repaired with air-drying repair varnishes. Painting large areas is, in principle, only possible with special industrial paints suitable for renovation of coverings. The surface to be painted should be limited only to the places that require it (scratches to the metal layer, corrosion centers, etc.). Preparation of the surface for painting should be carried out according to generally accepted rules. Any signs of corrosion should always be thoroughly removed – preferably with special brushes or fine sandpaper. Then, the surface to be repaired must be thoroughly dusted, degreased and cleaned. To degrease the surface, you can use gasoline or water with the addition of surfactants (preferably with the addition of 1-2% ammonia solution). The areas to be repaired may show differences in color compared to the original colors of the sheets due to the natural influence of atmospheric phenomena (aging of the paint under the influence of UV radiation).
Steel sheets with ColorCoat and Prisma coatings must not be used in:
- environment exposed to aggressive chemicals
- combination with materials with a different electrochemical potential.
ATTENTION – During inspection, cleaning, maintenance and repairs, safety rules must be strictly adhered to.

The company Pruszyński Sp. z o. o. is not responsible for any accidents resulting from the above activities.

THE COLORS

The PRUSZYŃSKI company guarantees the execution of each order in the same color (shade). However, due to the complexity of the coating processes, there may be differences in shades between individual deliveries.

The responsibility for the color is therefore limited to one delivery only.

Therefore, in the case of ordering sheets to a specific batch, please indicate on the order or inform the Merchant that it is a continuation of the order and provide a color sample.