fbpx

Multilayer panels PL-120

Produkto aprašymas

corePIR polyurethane
plate thickness120 mm
effective width1050/1000 mm
overall width1104/1054 mm
weight 1m 212.60 kg
min plate length2.0 mb
max board lengthsee – plate lengths
sheet thickness0.5 mm
type of external profilingtrapezoid – T

micro – M

wave – F

type of internal profilingtrapezoid – T
coatingspolyester glossy / matt, polyurethane, HPS200
accessoriesfastening systems, gaskets, flashings

 

PHYSICAL PROPERTIES

Material properties
Thermal conductivity λD0.022 W / mK
Heat transfer coefficient UD, S0.19 W / m2K
Core density40 ± 3 kg / m3
Libra12.60 kg / m2
Mechanical resistance
Compressive strength0.095 MPa
Tensile strength0.070 MPa
Shear strength0.075 MPa
Shear modulus of elasticity2.90 MPa
Bending strength in the span
Positive bending9.18 kNm / m
Positive bending, increased temperature9.18 kNm / m
Negative bending6.37 kNm / m
Negative bending, increased temperature5.66 kNm / m
Bending strength over internal support
Positive bending5.25 kNm / m
Positive bending, increased temperature4.69 kNm / m
Negative bending7.85 kNm / m
Negative bending, increased temperature6.99 kNm / m
Wrinkle stresses (outer surface)
In the span180 MPa
Increased temperature in the span180 MPa
Above the central support154 MPa
Increased temperature above the central support137 MPa
Ripple stresses (inner surface)
In the span125 MPa
Above the central support103 MPa
Other properties 
Reaction to fire (all applications)B-s1, d0
Fire resistanceEI30 (o ↔i)
Water permeabilityClass A 1200 Pa
Air permeability+ (C = 0.0860, n = 0.6638); – (C = 0.1616, n = 0.5103)
Water vapor permeabilityImpermeable
Airborne sound insulation25 (-3; -5) dB
Sound absorption0.15
DurabilityAll the colors

Recommendations for the selection of boards in the context of thermal loads

When designing, the temperature differences between the sandwich panel facings should be taken into account. The temperature gradients resulting from the difference in temperature between the outside temperature T 1 and the inside temperature T 2  depend on several factors:

  • purpose of the facility (temperature range inside the facility – T 2 )
  • object location – location in relation to the sun
  • color of the outer cladding (T 1 ).

Depending on latitude, altitude and distance from the sea on the European continent, four different levels of winter temperature (T1 – external cladding) are used:

  • 0, -10 o C,
  • 0, -20 o C, (e.g. Poland)
  • 0, -30 o C, (e.g. Scandinavian countries)

The temperature of the external cladding for roof panels covered with a layer of snow cover is 0 ° C.

For the calculations, the outside temperature in winter was assumed to be -20  o C.

The temperature of the outer cladding T 1  is the maximum in summer and depends on the color and degree of reflection of the surface. The values ​​of T 1 , which are the minimum for the Ultimate State (ULS) design and relevant for the Service Limit State (SLS) design, are taken as follows:

  • very bright colors R G  = 75-90 T 1  = +55 o C
  • bright colors R G  = 40-74 T 1  = +65 o C
  • dark colors R G  = 8-39 T 1  = +80 o C

where R G  – is the degree of reflection of rays in relation to magnesium oxide = 100%

The table below presents a classification broken down into color groups for individual colors available in the assortment of Pruszyński Sp. z o. o

PLATE LENGTHS

Permissible panel lengths depending on the cladding color (minimum length – 2.5 m) .

Color groupCOLORmax length (m) *
 WALL
group I

 very bright colors

RAL : 1015, 7035, 9001, 9002, 901018
group II 

bright colors

RAL : 1002, 1003, 1004, 1014, 1017, 1019, 1021, 1023, 1035, 2000, 2003, 2004, 2008, 2009, 5012, 5018, 5024, 6018, 6021, 6033, 7000, 7037, 7040, 9006, 902212
group III

 dark colors

RAL : 3000, 3002, 3003, 3005, 3011, 3013, 5002, 5005, 5009, 5010, 5011, 5022, 6000, 6003, 6005, 6011, 6020, 6029, 7015, 7016, 7022, 7024, 8016, 8017, 8023, 9005, 9007

 

RR : 750, 011, 028, 033, dark walnut, golden oak

9

 * length resulting from the limitation of the maximum extension / shortening of the slab

 

NOTE – Group III – dark colors

  • Recommendations for the selection of boards in the context of thermal loads

Taking into account that the dark-colored panels from group III are subject to much greater thermal loads than the very bright and light-colored panels from groups I and II, it should be assessed during the design, depending on the loads, what arrangement of panels on the wall is possible ( 1-span, 2-span, multi-span), horizontal or vertical arrangement. In addition, a very important matter is the selection of max. the length of the plates. The arrangement of the load-bearing structure should be designed for the appropriate static arrangement of the panels, taking into account the widths of the supports (transoms and purlins), their maximum spacing and the number of connectors.

In addition, during the design process, particular care should be taken to ensure that the following conditions are met:

• the method of fastening and the static system must be in accordance with the tables of permissible loads and spans (criteria met – ultimate limit state, operating limit state) *

• the length of the boards should be selected in such a way as to meet the limits indicated by the manufacturer of the boards **

• the panel assembly temperature must be taken into account. ***

• panels with facings with smooth profiling may be used / installed only in a single-span system

* For panels in dark colors, single-span systems are recommended; Otherwise, the intermediate supports may experience unacceptable by the Investor deformation of the external cladding of the panel. The waves in question meet the requirements of PN-EN 14509: 2013-12 in terms of permissible deviations, however, they may cause deterioration of the aesthetics of the panels, as a consequence of complaints.

** The maximum board lengths should be in accordance with the manufacturer’s guidelines, depending on the type of board and their application (roof / wall) – see LENGTHS. For plates in dark colors, longer than those mentioned in point 4, table 2, the company Pruszyński does not provide a guarantee, unless such use has been previously agreed in writing with the authorized representative of the company Pruszyński.

*** Installation of PIR sandwich panels with dark cladding (III color group) should be carried out at the outside air temperature ranging from + 10 ° C to + 35 ° C.

Immediately before assembly, (~ 20 min.) The dark cladding of the sandwich panel (usually it is the external cladding), should not be exposed to direct sunlight, as it may cause excessive heating of the cladding / cladding and its deformation.

The wall panels in the bundle are placed with the façade side up. It is recommended to shield the facade cladding in the package from the sun. If the slab packages on the construction site are stored in direct sunlight, it is recommended to put the first slab in the bundle away, cover it or turn the inside of the slab to the sun. Subsequent panels taken from the package should not be exposed to the sun for more than 20 minutes before fixing them.

It is necessary to pay attention to the above aspects during installation, because the temperature of the outside air affects the aesthetics of the facade and the correct operation of the panel.

In this case, deformation and damage to the panel are caused by high elongation of the cladding (e.g. at summer temperatures) in relation to the initial length (cladding length during installation). Installation of light and very light colors is possible in the temperature range from + 5 ° C up to + 35 ° C.

Failure to comply with the above guidelines may result in surface deformation on the plates and local loss of stability, for which the manufacturer is not responsible. In the case of colors not listed in the table, please contact the technical advisor of the Pruszyński company. The plate color may only be changed with the consent of the designer.

TRANSPORT RECOMMENDATIONS

Recommended means of transport for sandwich panels:

  • a truck (truck tractor + semi-trailer with a length not shorter than the length of the loaded plates) with the semi-trailer open or allowing side loading on both sides along its entire length
  • the weight of the load must not exceed the maximum load capacity of the set,
  • transport belts should be placed on the load at a distance of max. every 3 m, but not less than 2 belts for one package – the tension of the belts must not cause deformation of the panels.

STORAGE RECOMMENDATIONS

Sandwich panels should be stored in packages (posts), it is allowed to store a maximum of two packages on top of each other.

The table below shows the max. number of boards that can be placed in one package.

plate thicknessPWS-PIR-PL
60 mm18 pcs.
80 mm14 pcs.
100 mm11 pcs.
120 mm9 pcs
  • It is recommended to store the boards on an even surface (square, hall) on polystyrene joists or sleepers, which must be spaced at most every 2.5 m (for boards with a total length of up to 2.5 m, at least 3 underlays should be used).
  • It is allowed to store a maximum of two packages of boards up to 6m on top of each other, in the case of packages of boards over 1m, they should be stored individually. All plate packages must be stored on an even surface with the possibility of drainage.
  • During the storage of panels on the construction site, they should be protected against mechanical damage, exposure to UV rays, aggressive environment (acids, fertilizers, salts and other corrosive agents), precipitation, strong wind and others.
  • It is recommended to store the packages under a roof in ventilated rooms
  • The boards should be stored on an even surface (square, hall) on joists, polystyrene or wooden sleepers, which must be spaced at most every 2.5 m (for boards with a total length of up to 2.5 m, at least 3 sleepers should be used. ).
  • Protective films are used to additionally protect the surface of the panels against mechanical damage, stresses and impacts that may occur during transport or handling. The foils never release you from the obligation to properly protect the panels during storage.
  • It is recommended to remove the protective film before mounting the elements on the facade or roof of the building. The foil should be removed when the air temperatures are positive, because the adhesive delaminates at negative temperatures and some of its components may remain on the sheet.
  • Improper sheet storage may cause difficulties in removing the protective foil and leave traces of glue on the surface of the boards. In such cases, complaints about the remnants of the adhesive from the protective film will not be considered by the Manufacturer.
  • In the case of panels with hidden fasteners, make sure that the foil is removed from the inside of the longer lock before assembly.

ATTENTION !!!

In the case of wall panels with visible fastening (applies to PIR panels), the upper side of the panels in the package is the façade side, which should be taken into account in particular!

MAINTENANCE AND WASHING

In order to extend the service life of roofs and facades made of coated metal sheets, they should be regularly inspected and maintained.

  • Inspection –  Once a year (preferably in spring), the roof / facade should be inspected for early detection of possible damage.
  • Sheet cleaning – Roofs / facades made of coated sheet metal require cleaning at least once a year. Dirt settling on the sheet can cause uneven discoloration (the result of uneven exposure to UV rays), and also reduce corrosion resistance (dirt retains moisture on the sheet and gradually damages it). Dirty and stained places can be cleaned with a soft brush and water (temperature max. 60 ° C). If necessary, it is allowed to add a mild detergent to the water (pH 6 ÷ 7, max. 10% solution). Pressurized water (max. 100 bar) can also be used for cleaning, however, the water jet cannot be used too close to the board surface (min. 30 cm), and it cannot be directed perpendicularly to the surface. At the connectors, the stream of water should be directed downwards so that to avoid the ingress of pressurized water into the gaps around the fittings. Old board coatings must be handled with extreme care. Washing should be carried out from the top downwards and the cleaned area should be immediately and thoroughly rinsed with clean water.
  • Scouring powders, nitro solvents, chlorine solutions, aromatic agents as well as agents containing ammonium chloride or sodium salts must not be  used.
  • Damage – Any damage during the warranty period must be consulted with the Roof / facade Contractor and may be made only with his written consent. Damage to small areas is repaired with air-drying paints, while painting large areas is generally only possible with special industrial paints suitable for renovation of coverings. The surface to be painted should be limited only to the places that require it (scratches to the metal layer, corrosion centers, etc.). Preparation of the surface for painting should be performed according to generally accepted rules. Any signs of corrosion should always be thoroughly removed – preferably with special brushes or fine sandpaper. Then, the surface to be repaired must be thoroughly dusted, degreased and cleaned. To degrease the surface, you can use gasoline or water with the addition of surfactants (preferably with the addition of 1-2% ammonia solution). The areas to be repaired may show differences in color compared to the original colors of the sheets due to the natural influence of atmospheric phenomena (paint aging under the influence of UV radiation).
  • CAUTION – During inspection, cleaning, maintenance and repairs, safety rules must be strictly adhered to.

COLOR

The colors below may differ from reality.

  • * – available coatings with a thickness of 0.50 mm
  • ** – available coatings with a thickness of 0.50 and 0.70 mm
  • *** – coatings available in thicknesses of 0.50, 0.70 and 1.00 mm
AZ - aluzincAZ – aluzinc
Polyester gloss 25 um
RAL 9010 ***RAL 9010 ***
RAL 9002 **RAL 9002 **
RAL 7035 **RAL 7035 **
RAL 9006 ***RAL 9006 ***
RAL 9007 **RAL 9007 **
RAL 7000 *RAL 7000 *
RAL 7024 *RAL 7024 *
RAL 7016 **RAL 7016 **
RAL 5010 **RAL 5010 **
RAL 6029 **RAL 6029 **
RAL 6005 *RAL 6005 *
RAL 1021 *RAL 1021 *
RAL 1002 **RAL 1002 **
RAL 1015 *RAL 1015 *
RAL 8023 *RAL 8023 *
RAL 8004 *RAL 8004 *
RAL 3016 **RAL 3016 **
RAL 3005 *RAL 3005 *
RR 028 *RR 028 *
RAL 3011 **RAL 3011 **
RAL 8017 **RAL 8017 **
RR 032 *RR 032 *
RAL 9005 *RAL 9005 *
Golden Oak*Golden Oak*
PMG 35 um
PMG C. WalnutPMG C. Walnut
PMG RR 011PMG RR 011
PMG RR 750PMG RR 750
PMG RR 028PMG RR 028
PMG RR 032PMG RR 032
PMG RAL 8017PMG RAL 8017
PMG RR 033PMG RR 033
PMG RAL 7016PMG RAL 7016
Polyurethane – PURLAK 50 um
PU RAL 8004PU RAL 8004
PU RR 028PU RR 028
PU RAL 8017PU RAL 8017
PU RAL 9005PU RAL 9005
PU RAL 7016PU RAL 7016
Polyurethane – PURMAT 50 um
PUM RR 750PUM RR 750
PUM RR 011PUM RR 011
PUM RR 028PUM RR 028
PUM RAL 8017PUM RAL 8017
PUM RR 033PUM RR 033
PUM RAL 7016PUM RAL 7016
+


    Pasirinkti failusPrisegti failą

    Užsiprenumeruokite naujienlaiškį
    +
    Gaukite geriausius pasiūlymus, informaciją apie akcijas ir naujienas pirmieji.